Start with the loads, not the box
The A1100.5 is a five-channel amp, but its channels are not identical. Channels 1–4 are rated at 90W x 4 at 4Ω and 125W x 4 at 2Ω; channel 5 is rated at 400W x 1 at 4Ω and 600W x 1 at 2Ω, all at 14.4V. Before you buy speakers or a sub, decide which four speakers you will drive and what impedance they present, then choose a sub whose voice-coil configuration matches either the 4Ω or 2Ω rating. If your sub can only be wired to a load the amp does not list, this is the wrong amplifier for that sub.
This matters because the amp’s power figures are tied to those two load options. A dual-voice-coil sub can often be wired to either 2Ω or 4Ω, but the catalog does not state whether the A1100.5 is stable below 2Ω, so do not assume a 1Ω load is safe. The supplied information also does not confirm bridgeable operation, so plan on using the five channels as four speaker channels plus one sub channel.
A1100.5 power ratings to plan around
- AudioControl A1100.5 Altitude 5-Channel Amplifier: Rated continuous (RMS) power at 14.4V: 90W x 4 @ 4Ω, 125W x 4 @ 2Ω, 400W x 1 @ 4Ω, 600W x 1 @ 2Ω. These are the only load/power pairs the catalog confirms, so speaker and sub impedance choices should land on 4Ω or 2Ω.

AudioControl A1100.5 Altitude 5-Channel Amplifier - AudioControl A1100.5 Altitude 5-Channel Amplifier: Dimensions: 14” W x 6.7” D x 2.1” H; weight: 7.95 lbs. The shallow, wide chassis affects where you can mount it—under a seat, on a board, or in a side panel—before you run any wire.
Wiring order for a five-channel install
Work from the power source outward. The catalog lists a 4 AWG power/ground wire gauge and a 120A recommended fuse rating; those are the numbers to build your main power run around. The steps below follow the order that avoids pulling panels twice.
- 1. Mount the amp and confirm clearance: The A1100.5 measures 14” W x 6.7” D x 2.1” H. Check that the chosen location leaves room for the power and ground terminals, RCA or speaker-level connectors, and the optional ACR-1 remote level control. The catalog does not list a minimum clearance or ventilation distance, so follow the vehicle’s own space constraints rather than a made-up number.
- 2. Run 4 AWG power and ground with a 120A fuse: Use the supplied 4 AWG gauge and 120A fuse rating as the basis for the main power feed. Keep the ground run short and to bare metal. The catalog does not specify fuse type or location, so use a fuse holder rated for the wire and current you are running.
- 3. Choose line-level or speaker-level input: The A1100.5 accepts up to 6V on its line-level inputs and up to 20V on its speaker-level inputs, with six preamp inputs. If you are keeping a factory radio, speaker-level input is the path the catalog supports. If you have an aftermarket head unit with RCA outputs, use line-level.
- 4. Connect speakers to channels 1–4 and the sub to channel 5: Match each speaker’s impedance to the 4Ω or 2Ω ratings above. The catalog does not list terminal layout or channel labeling, so confirm those on the unit itself before connecting.
- 5. Set turn-on and signal sense: The amp includes GTO Signal Sense, which turns the amp on automatically when it detects an audio signal. That can simplify wiring with a factory system that lacks a dedicated remote turn-on wire. The catalog does not state whether GTO can be disabled, so check the unit’s controls if you prefer a conventional remote turn-on.
Input level and vehicle electrical notes
The A1100.5 is listed as EV compliant up to 17V and start-stop compliant. Those two claims matter if you drive an electric vehicle or a modern car that drops voltage at stoplights: the amp is described as working with those systems rather than needing a separate voltage conditioner. They do not, however, tell you how much current the amp draws at full output—the catalog does not supply a current-draw figure, so size your alternator and battery plans around the 120A fuse rating rather than an invented amperage number.
On the input side, the 6V line-level and 20V speaker-level maxima are the limits to respect. A factory amplifier or high-output OEM radio can exceed 6V on its RCA-level signal, which is why the speaker-level input exists. If you are unsure which signal your vehicle provides, the speaker-level path is the safer documented option.
Input and protection features that shape the install
- AudioControl A1100.5 Altitude 5-Channel Amplifier: Line-level inputs: 6V max; speaker-level inputs: 20V max; six preamp inputs. Determines whether you can keep a factory head unit or need line-output converters.
- AudioControl A1100.5 Altitude 5-Channel Amplifier: GTO Signal Sense automatically turns the amp on when it detects audio signals. Can reduce remote-turn-on wiring in factory-integrated systems.
- AudioControl A1100.5 Altitude 5-Channel Amplifier: Valet Mode limits maximum volume to 25% when activated. Useful if the vehicle is shared or serviced; it protects the system from accidental full-volume events.
Setting crossovers and bass contour
The A1100.5 uses Linkwitz-Riley crossovers with Off, High Pass, and Low Pass modes, plus a variable subsonic filter and ParaBASS low-frequency contouring. The catalog does not list the crossover frequency ranges, so you cannot pre-set exact frequencies from the spec sheet alone—set them by ear or with a measurement tool after the system is running.
A practical order: start with the crossovers Off, confirm all channels play, then set the high-pass on channels 1–4 to keep low bass out of the door speakers, set the low-pass on channel 5 to match the sub’s usable range, and bring in the subsonic filter only if you need to protect a ported sub below its tuning. ParaBASS is a contour control, not a fixed boost frequency, so adjust it after the crossovers are set. The catalog does not state a recommended starting point for any of these controls, so treat them as tuning tools rather than preset values.
Optional ACR-1 and system-matching notes
- Remote level control: The ACR-1 is an optional remote for subwoofer volume. If you want dash-level bass control, plan its cable route during the install rather than after the panels are back on.
- Speaker and sub matching: AudioControl positions the Altitude series as a match for its PNW speakers and Space or Spike subwoofers. That is a manufacturer pairing claim, not a guarantee of audible improvement; the electrical match still has to land on the 4Ω or 2Ω ratings above.
- What the catalog does not confirm: The supplied information does not list bridgeable operation, minimum impedance below 2Ω, crossover frequency ranges, terminal layout, or a current-draw figure. Plan around those gaps rather than assuming a value.


